Hello, welcome to visit Shandong Linyi Kuntai Machinery Equipment Co., Ltd official website!
Ф 2.2 by 8 meters of second-hand ball mill
Ball mill - development issues
Ball mill is pretty expensive configuration: as the ball mill cylinder speed and low (15 ~ 25 RPM), such as using ordinary motor drive, is expensive deceleration device.
Production costs are high: grinding body at the same time of impact and grinding materials, by grinding strip itself, the cylinder body parts such as lining board also be ground off, so in the cement production process, crushing assignments (raw meal preparation, cement grinding) consumed by the amount of iron is a lot of, according to the analysis, about every tons of cement production of steel consumption is about 1 kg.
Low working efficiency, such as: in the process of production of cement, electricity is used for crushing operations account for about two-thirds of all, according to statistics, every tons of cement production the power consumption of not less than 70 kilowatt hours, but this part of the electrical energy effective utilization rate is very low, according to the analysis, the input power is used for crushing materials of cement ball mill (doing useful work) accounts for only a small part of the power consumption of about 5% ~ 5%, and most of the power consumption in other aspects, mainly is transformed into heat and sound energy and disappear, this is a big waste.
Hulking: large total weight of the ball mill can be as big a few hundred tons, such one-time investment must be big.
The ball mill product parameters
More information about second-hand ball mill, please go to http://www.coiffure-services.com at any time
規格型號
筒體轉速（r/min）
裝球量(t)
進料粒度(mm)
出料粒度(mm)
產量
電機功率(kw)
重量(t)
(t/h)
Ф900×1800
36～38
1.5
≤20
0.075-0.89
0.65-2
18.5
4.6
Ф900×3000
36
2.7
≤20
0.075-0.89
1.1-3.5
22
5.6
Ф1200×2400
36
3
≤25
0.075-0.6
1.5-4.8
30
12
Ф1200×3000
36
3.5
≤25
0.074-0.4
1.6-5
37
12.8
Ф1200×4500
32.4
5
≤25
0.074-0.4
1.6-5.8
55
13.8
Ф1500×3000
29.7
7.5
≤25
0.074-0.4
2-5
75
15.6
Ф1500×4500
27
11
≤25
0.074-0.4
3-6
110
21
Ф1500×5700
28
12
≤25
0.074-0.4
3.5-6
130
24.7
Ф1830×3000
25.4
11
≤25
0.074-0.4
4-10
130
28
Ф1830×4500
25.4
15
≤25
0.074-0.4
4.5-12
155
32
Ф1830×6400
24.1
21
≤25
0.074-0.4
6.5-15
210
34
Ф1830×7000
24.1
23
≤25
0.074-0.4
7.5-17
245
36
Ф2100×3000
23.7
15
≤25
0.074-0.4
6.5-36
155
34
Ф2100×4500
23.7
24
≤25
0.074-0.4
8-43
245
42
Ф2100×7000
23.7
26
≤25
0.074-0.4
8-48
280
50
Ф2200×4500
21.5
27
≤25
0.074-0.4
9-45
280
48.5
Ф2200×6500
21.7
35
≤25
0.074-0.4
14-26
380
52.8
Ф2200×7000
21.7
35
≤25
0.074-0.4
15-28
380
54
Ф2200×7500
21.7
35
≤25
0.074-0.4
15-30
380
56
Ф2400×3000
21
23
≤25
0.074-0.4
7-50
245
54
Ф2400×4500
21
30
≤25
0.074-0.4
8.5-60
320
65
Ф2700×4000
20.7
40
≤25
0.074-0.4
12-80
400
94
Ф2700×4500
20.7
48
≤25
0.074-0.4
12-90
430
102
Ф3200×4500
18
65
≤25
0.074-0.4
按工藝條件定
800
137
